Constant Current Source Theory Testing
by Lewis Loflin
Note: click on any image for larger view.
I have two constant current source assemblies. One is for use with a microcontroller, the other simply manual adjustment.
See the following photo for the two: Constant Current Sources I built. The one on the wooden board is the one used here.
The smaller PC board assembly is for my webpage Arduino Controlled Power Constant Current Source.
If one is new to electronics or need a short review of current and voltage is series parallel circuits see my webpage Review Ohm's Law for Trouble-Shooting CCS Circuits.
This is based on my earlier work with this device and the link to that page and a YouTube video:
Here I'll update and go beyond the old design and look at uses, limitations, and theory of operation.
Let's define what a constant current source is off the web:
"A constant current source is a power source which provides a constant current to a load, even despite changes and variance in load resistance...A constant current source is, thus, a very valuable component because it can supply steady current even if there are changes in resistance, even a wide variance in the resistance. This comes in use when a circuit needs a steady current supply, without fluctuations."
It goes far beyond that. When developing or trouble shooting a current limiter, and that is what it really is, protects components from damage. In fact I use mine when constructing and programming H-bridge motor control circuits.
In fact I used my older CCS to build the newer version in case of wiring mistakes. In one case I dead shorted the output with no harm to any part.
Fig. 1 is my test setup. There is much more going on than the definition suggests.
Fig. 2 is the schematic to the test setup. Note the upper right corner is the CCS schematic. It consists of a PNP pass transistor and an LM317 used as a variable constant current source.
The LM317 controls the base-emitter current of Q1. That in turn sets the emitter-collector current which is the output current.
The Iset control sets overall output current.
The input voltage is 18-volts. Note the next three images.
Fig. 3 illustrates 1 amp through 5-Ohms is 5-volts. The input voltage is 18-volts, so where is my 13-volts?
It is dropped across the pass transistor Q1 where the emitter-collector current is also 1 amp.
The power supply produces a little over 1 amp with the extra for the LM317 circuit.
The load being two, 10-Ohm 25-watt resistors split the 5-watts of power equally. But Q1 drops 13-volts at 1 amp or 13-watts.
Q1's heat sink can get hot and I added a small fan for cooling. Yes there is some drift due to heat with Q1, but is minimal.
The best way to reduce heat generated in Q1 is use a lower input voltage. In the case 8-12-volts is plenty.
Fig. 4 we supply 2 amps to the load producing 10-volts. The load receives 20-watts (voltage times current) split between the the two parallel 10-ohm resistors.
Q1 drops 8-volts at 2 amps for 16-watts.
Here we have 3 amps delivers 15-volts and 45 watts to the load. Q1 pass transistor dissipates 15-watts.
Note the voltage drop across the load is getting close to the input voltage of 18-volts. Above 16-volts the circuit will no longer regulate or limit the current.
As a general rule load voltage times current must never exceed 85% of the input voltage. This can vary in other circuits but is the rule I follow.
The following three examples illustrate the real world. Remember with 18-volts input and a 5-Ohm load we can deliver a little over 3 amps, over 45-watts to the load.
Load Resistance versus Input Voltage
In Fig. 6 I removed one of the 10-Ohm parallel resistors. My load load resistance is now 10-Ohms and I adjusted the current for 1 amp. I got 10-volts across the load.
What is my maximum current? Will I get 2 or 3 amps? The answer is no.
Try adjusting for 2 amps the load voltage exceeds the input voltage. The best we can do is 1.6 amps.
In Fig. 7 two 20-Ohm resistors in parallel produces a 10-Ohm load. Again maximum current is still 1.6 amps.
In Fig. 8 I removed one 20-Ohm resistor for a load of 20-ohms. My maximum current is ~850mA.
Conclusion
Output voltage from a constant current source is set by the current and load resistance.
Changing load resistance won't change the current, but changes the load voltage. This is limited by the input voltage.
As a rule choose a power supply greater than the needed load voltage. Don't use a 24-volt input to operate a 2-volt load. In my opinion keep the input voltage about 25% above the load voltage if possible.
My test on the circuit also revealed changing the input voltage will change the output voltage. Use a stable input voltage.
A constant current source is NOT a voltage regulator.
Date: 7-11-2021
- Constant Current Source Theory Testing
- Arduino Measures Current from Constant Current Source
- Review Ohm's Law for Trouble-Shooting CCS Circuits
- Arduino Power Magnetic Driver Board for Stepper Motors
- Arduino Controlled Power Constant Current Source
Related video to above:
- Constant Current Source Multimeter Trouble Shooting
- Ohm's Law Review for Constant Current Source
- Arduino Unipolar Stepper Motor Driver Board with Arduino Code
- Arduino Controlled Constant Current Source
- Related to above:
- Using a Unipolar Stepper Motor with a Arduino
- ULN2003A Darlington Transistor Array with Circuit Examples
- Tutorial Using TIP120 and TIP125 Power Darlington Transistors
- YouTube
- ULN2003A Transistor Array with Arduino
- Arduino Stepper Motor Control
- Using the TIP120 & TIP125 Darlington Transistors with Arduino
- LM317 High Power Constant Current Source Circuit
- Adjustable LM317 High Power Current Source
- ULN2003A Darlington Transistor Array with Circuit Examples
- ULN2003A Transistor Array with Arduino
- Constant Current Circuits with the LM334, LM317
- Constant Current Source Tutorial YouTube
- Constant Current Circuits with LM317, LM334, etc.
- Experiments with TL431 Shunt Regulator
- TL431 Precision Current Regulator Circuits
- TL431 Based Current Limiter Constant Current Source Circuits
- TL431 Shunt Regulator Circuits
- Simple Triac-SCR Test Lab for You Tube
- Constant Current Circuits with the LM334
- LM334 CCS Circuits with Thermistors, Photocells
- LM317 High Power Constant Current Source Circuit
- LM317 Constant Current Source Circuits
- LM317 Adjustable Voltage Source Current Boost
- LM317 Constant Current Source for Lighting LEDs
- 3 Amp LM741 Op-Amp Constant Current Source
- Comparator Circuits:
- Comparator Theory Circuits Tutorial
- Comparator Hysteresis and Schmitt Triggers
- Voltage Comparator Information And Circuits
- Looking at Window Comparator Circuits
- Opto-Coupler SCR and Triac Circuits:
- Improved AC Zero Crossing Detectors for Arduino
- Zero-Crossing Detectors Circuits and Applications
- Basic Triacs and SCRs
- Solid State AC Relays with Triacs
- Light Activated Silicon Controlled Rectifier (LASCR)
- Light Activated SCR Based Optocouplers Circuit Examples
- Comparing Photo Triac, Photo SCR Opto-Couplers
- Silicon Controlled Rectifier Review and Circuits
- Silicon Controlled Rectifiers Connected as Power Triacs